12.2.2 Chemical Pump Assembly, Wilden P.025 The Chemical Pump Assembly, Wilden P.025 is a loose ship package that allows for chemical delivery from a customer supplied container to the SaniCab cabinet washer’s chemical injection port(s). The 24V DC outputs
described in Section 8.5 Automation Interfaces are to be used with the chemical pump assembly's solenoid valves for metering of the chemical. The following components are packaged and shipped loose for installation by others: • One (1) PVC suction lance (43") with foot valve for placement in a 55-gallon chemical container (container by others) • One (1) Air operated diaphragm pump − Duty: 3 gpm @ 45 psi − Instrument Air Requirements: 3 scfm @ 100 psi − Construction: Polypropylene body with PTFE diaphragms • One (1) 0.25" solenoid valve (24V DC) with filter / regulator for control of the pump. The pneumatic components and piping are made of brass. • One (1) 304ss wall mounting bracket allowing the pump assembly to be wall mounted near the chemical container • One (1) Manual bleed valve to aid in priming the pump • One (1) 0.25" check valve to prevent the siphoning of the cleaning chemicals
Bleed Valve
Check Valve
Suction Lance with Foot Valve
• Thirty (30) Feet of 0.5" Polyethylene tubing for the pump’s suction and discharge lines • Eight (8) Feet of 0.375" Polyethylene tubing for the pump’s bypass/priming line 12.2.3 Spray Gun Assembly The spray gun assembly is used to manually pre-rinse heavy soils off parts prior to being loaded into the SaniCab. The following components are shipped loose for installation by others: • One (1) Spray gun assembly • One (1) Water inlet connection assembly; 1.5" tri-clamp reduced to a ½" FNPT manual ball valve
• One (1) 40' long hose with MNPT swivel connections on each end • One (1) Quick connect adapter for hose connection to spray gun • One (1) Hose rack 12.2.4 Conveyorized Strainer Catch Pan The Conveyorized Strainer Catch Pan is attached to the conveyorized strainer outlet and is intended to catch the solids that are automatically strained from the SaniCab P. The catch pan is fabricated of 304ss with welds color cleaned and holds approximately 0.6 cubic feet of soils.
NOTE: • This accessory requires the Automated Conveyorized Mesh Screen recirculated straining option.
12.2.5 Exhaust Ducting Components Exhaust ducting components are utilized to connect the exhaust fan outlet of the chamber, transition to 12" Ø round ducting, and direct exhaust air to a suitable location (e.g., through a roof penetration). The components are loose shipped and installed by others.
Table 15: Exhaust Ducting Accessories
Informational Data
Accessory Name
Bend Radius
L x W / Diameter Length
Description of Use
Exhaust Ducting - Transition (5" x 8.5" to 12" Ø)
5" x 8.5" to 12" Ø 12.269"
N/A Connect exhaust fan outlet to round ducting
Exhaust Ducting - Elbow (90°) Exhaust Ducting - Elbow (45°) Exhaust Ducting - Straight (5') Exhaust Ducting - Seal Kit (5" x 8.5")
12" Ø 12" Ø 12" Ø
N/A 18.0675" 90° transitions
N/A
14.5"
45° transitions
5'
N/A Straight run for round ducting
N/A N/A
N/A N/A
N/A Gasket (EPDM) and hardware for fan outlet connections
Exhaust Ducting - Seal Kit (12" Ø)
N/A Gasket (EPDM) and hardware for all round ducting connections
NOTE: • All SaniCab P exhaust fan connections are 5" x 8.5".
sanimatic.com 31
TD-0003.7
Powered by FlippingBook